|
Click
HERE
for Motor Data Page to
help you select the best motor for your application |
|
Picture |
Description |
Price |
Add to Cart |
|
Click
HERE for larger
picture |
M-A-E
Twin Brushless CD-ROM
Direct Drive Outrunner Motors
Pre-wired (plug-and-fly) for twin-power applications.
Male Deans 3-pin micro connector is already installed.
Mating female Deans is provided for your ESC. Motors have same spec's as our
25T M-A-E listed below. Recommend 9x5 props on 2S or
8x4 props on 3S. Generates 16-21 ounces of thrust and
weighs just 38 grams! Run these setups on a
single 9-10A ESC (see below)
Requires
two
3.0mm Prop Saver or
Adapter |
$69.95 |
|
|
Click
HERE for larger picture |
M-A-E "Slo-Fly"
Brushless 25-turn Outrunner
Direct-drive CD-ROM, 22.7mm, NE50 Magnets. Weighs only
18 grams. Draws 4.8A
on 10x6 prop and 2S lipoly. Produces 10+ ounces of thrust. Uses
MAE Laser Mount for Westport (see below)
Great for Nemesis 3D-II and SLICK - slow speed, high
thrust applications
Requires
3.0mm Prop Saver or
Adapter |
$29.95 |
|
|
Click
HERE for larger
picture |
M-A-E "Madness"
Brushless
17-turn Outrunner
Direct-drive CD-ROM, 22.7mm, NE50 Magnets. Weighs only
18 grams. Turns a 5x5
prop on 3S, 7x5 or 8x4 on 2S. Uses MAE Laser Mount for Westport
(see below)
Great for higher pitch- speed applications
Requires
3.0mm Prop Saver or
Adapter |
$29.95 |
|
|
Click
HERE for larger
picture |
M-A-E "Stealth"
Brushless
15-turn Outrunner
Direct-drive CD-ROM, 22.7mm, NE50 Magnets. Weighs only
18 grams. Turns a 5x5
prop on 3S, 7x4 on 2S. Uses M-A-E Laser Mount (see below)
Great for higher pitch- speed applications
Requires
3.0mm Prop Saver or
Adapter |
$29.95 |
|
|
 |
Replacement Rotor Assembly for
M-A-E/Westport Motors
Complete assembly, ready-to-run. Fixes motors with bent
rotors resulting from crash damage. Simple "pop-on"
installation. |
$15.95 |
|
|
 |
M-A-E Laser Mount for adapting
LensRC, Westport,
M-A-E and other small brushless outrunner motors to the GWS IPS motor stick.
Fits motors with 8mm diameter bearing tube.
Use for our Nemesis
3D-II, SLICK, TumbleBuddy Jr. |
$3.95 |
|
|
 |
Generic 10-amp ESC
for Brushless Motors
- Weight: 8g
- Use with 2-3 cell Lipo
- Auto throttle calibration
- AUTO CELL DETECT!!!
- Constant Current: 10A / 15Amp Burst
(10Seconds)
- Timing: Auto
- Auto Voltage Cutoff
- Auto shut down when signal is lost
NOTE: Requires JST female connector for lipolys -- see
below |
$18.95 |
|
|
 |
Castle
Thunderbird-9 Programmable ESC for brushless motors from the top domestic ESC manufacturer. Has
all the
Important Features you need at an attractive price!
Weighs just 8 grams with wires.
NOTE: Requires JST female connector for lipolys -- see
below |
$29.95 |
|
|
 |
Castle Phoenix-10 Programmable
ESC for brushless motors.
Weighs just 6 grams with wires.
MORE INFO
When you buy your
ESC from us, we upgrade it to the latest software from Castle
and program it for auto-detecting 2 or 3 cell lipoly and it then
automatically sets the correct cut-off voltage for your battery.
NOTE: Requires JST female connector for lipolys -- see
below |
$59.95 |
|
|
|
Plug 'n Fly -
We will solder battery and motor connectors to your ESC and
motor, and test-run your setup.
This is for LABOR
ONLY, and does not include the cost of the components which must
be purchased separately on this same order. This is for
those who can't or don't want to do their own motor-ESC hookup.
|
$11.95 |
|
|
 |
Castle PHX-Link USB Programmer
for programming Castle brushless ESCs from your PC.
MORE
INFORMATION |
$25.95 |
|
|
 |
JST female connector for ESC
NOTE:
Use
with ESC for lipoly plug-in |
$1.95 |
|
|
|
 |
Deans 3-pin
Connector for Motor-ESC
For connecting your brushless motor to your ESC. Good for
up to 10 amps. Includes 6 pcs heat shrink tubing. |
$1.95 |
|
|
|
|
|
